Artee Flow Controls Private Limited

The ME series of Gefran, are pressure transmitters forusing in High temperature environment. The main characteristic of this series is the capability toread temperature of the media up to 400 Degree C. The constructive principle is based on the hydraulic trasmissionof the pressure. The fluid-filled system assures the temperature stability. The phisical measure is transformed in a electrical measureby means the strain-gauge technology.

Features:

• Fluid-filled system for temperature stability
• Mercury filling volume: ME0 (30mm3); ME1, ME2, ME3 (40mm3)
• 1/2-20UNF, M18x1.5 standard threads; other types available on request
• Autozero function on board / external option
• Drift Autocompensation function (SP version)
• Standard diaphragm is 15-5 PH stainless steel with GTP+ coating
• 17-7 PH corrugated diaphragm with GTP+ coating for ranges below 100 bar-1500 psi
• GTP+ (advanced protection) Coating with high resistance against corrosion, abrasion and high temperature

Autozero Function:

• All signal variations in the absence of pressure can be eliminated by using the Autozero function.
• This function is activated by closing a magnetic contact located on the transmitter housing.
• The procedure is permitted only with pressure at zero.
• The Autozero function is activated through a magnetic contact (external magnet supplied with the sensor).
• See the manual for a complete Autozero function explanation.

Autocompensates Influence of Melt Temperature:

• Thanks to internal self-compensation, the MSP series transmitter cancels the effect of pressure signal variation caused by variation of Melt temperature.
• This reduces at the minimum the read error caused by heating of the filling fluid (typical of all sensors built with “filled” technology).

Load Diagram:

• The diagram shows the optimum ratio between the load and supply voltage of the 4...20mA transmitter.
• For a correct use, choose any combination of load resistance and supply voltage, in the shaded area.

ME2-6-M-B07C-1-4-D-000:

• Melt pressure transmitter with type “J” thermocouple, 4...20mA output, 6-pin connector, 1/2-20UNF thread, 700 bar full scale, 0,5% accuracy class, 153 mm (6”) rigid stem, 457mm (18”) flexible capillary.

MSPE0-6-M-P03M-1-4-0-000:

• Melt pressure transmitter autocompensated version, rigid stem, 4...20mA output, 6-pin connector, 1/2-20UNF thread, 3000 psi full scale, 0,5% accuracy class, 153 mm (6”) rigid stem.

Part of the SmartLine family of products, the STR800 is a series of high-performance pressure transmitters hydraulically matched and optimized with a complete set of remote diaphragm seals. Utilizing the same high-performance sensor technology of the ST 800 product line Honeywell has optimized the mechanical and hydraulic designs in order to minimize the typical effects of temperature on remote seal systems.

Best in Class Transmitter:

• Automatic static pressure & temperature compensation
• Multiple local display capabilities
• External zero, span, & configuration capability
• Polarity insensitive electrical connections
• Comprehensive on-board diagnostic capabilities
• Integral Dual Seal design for highest safety based on ANSI/NFPA 70-202 and ANSI/ISA 12.27.0
• World class overpressure protection
• Full compliance with SIL 2/3 requirements
• Modular design characteristics
• Available with 15-year warranty

Typical Diaphragm Seal applications:

• High Process Temperatures
• Viscous or Suspended Solids
• Highly Corrosive Process Materials
• Sanitary Applications
• Applications with Hydrogen Permeation Possibilities
• Level Applications with Maintenance Intensive Wet Legs
• Applications requiring remote Transmitter Mounting
• Tank Applications with Density or Interface Measurements

Communications/Output Options:

• Honeywell Digitally Enhanced (DE)
• HART (version 7.0)
• Foundation TM Fieldbus

Description:

• The SmartLine family of gauge pressure, differential pressure, and absolute pressure transmitters is designed around a high-performance piezo-resistive sensor.
• This one sensor actually integrates multiple sensors linking process pressure measurement with on-board static pressure (DP Models)
• Temperature compensation measurements resulting in the best total performance available.
• This level of performance allows the ST 800 to replace virtually any competitive transmitter available today.

Unique Indication/Display Options:

• The ST 800 modular design accommodates a basic alphanumeric LCD display or a unique advanced graphics
• LCD display with many unparalleled features.

Advanced Graphics LCD Display:

• Modular (may be added or removed in the field)
• 0, 90, 180, & 270 degree position adjustments
• Standard and custom measurement units available.
• Up to eight display screens with 3 formats are possible (Large PV with Bar Graph or PV with Trend Graph)
• Configurable screen rotation timing
• Display Square Root capabilities may be set separately from the 4-20mA dc output signal
• Unique “Health Watch” indication provides instant visibility of diagnostics
• Multiple language capability. (EN, GE, FR, IT, SP, RU, TR, CN, JP)

Integral Three Button Configuration Option:

• Suitable for all electrical and environmental requirements,
• SmartLine offers the ability to configure the transmitter and display via three externally accessible buttons when either display option is selected.
• Zero/span capabilities are also optionally available via these buttons with or without selection of a display option.

Part of the SmartLine family of products, the STA800 and
STA80L are high performance absolute pressure transmitters featuring piezoresistive sensor technology combining pressure sensing with on chip temperature compensation capabilities providing high accuracy, stability and performance over a wide range of application pressures and temperatures. The SmartLine family is also fully tested and compliant with Experion PKS providing the highest level of compatibility assurance and integration capabilities. SmartLine easily meets the most demanding application needs for pressure measurement applications.

Features:

• Automatic temperature compensation
• Response times as fast as 80ms
• Multiple local display capabilities
• External zero, span, & configuration capability
• Polarity insensitive electrical connections
• Comprehensive on-board diagnostic capabilities
• Integral Dual Seal design for safety based on ANSI/NFPA 70-202 and ANSI/ISA 12.27.0
• Full compliance to SIL 2/3 requirements as a standard.
• Modular design characteristics
• Available with 15 year warranty
• Plugged Impulse Line Detection Option
• Dual/Triple Calibration Option (HART & Fieldbus Only)

Description:

• The SmartLine family of gauge pressure, differential pressure, and absolute pressure transmitters is designed around a high performance piezo-resistive sensor.
• This one sensor actually integrates multiple sensors linking process pressure measurement with on-board static pressure (DP Models) and temperature compensation measurements resulting in the best total performance available.
• This level of performance allows the ST 800 to replace virtually any competitive transmitter available today.

Basic Alphanumeric LCD Display:

• Modular (may be added or removed in the field)
• 0, 90,180, & 270 degree position adjustments
• Configurable (HART only) and standard (Pa, KPa, MPa, KGcm2, Torr, ATM, inH2O, mH2O, bar, mbar, inH2O, inHG, FTH2O, mmH2O, mm HG, & psi) measurement units
• 2 Lines 16 Characters (4.13H x 1.83W mm)
• Square root output indication

Advanced Graphics LCD Display:

• Modular (may be added or removed in the field)
• 0, 90, 180, & 270 degree position adjustments
• Standard and custom measurement units available.
• Up to eight display screens with 3 formats are possible (Large PV with Bar Graph or PV with Trend Graph)
• Configurable screen rotation timing (1 to 30 sec)
• Display Square Root capabilities may be set separately from the 4-20mA dc output signal
• Unique “Health Watch” indication provides instant visibility of diagnostics
• Multiple language capability. (EN, GE, FR, IT, SP, RU, TR, CN and JP)

Integral Three Button Configuration Option:

• Suitable for all electrical and environmental requirements,
• SmartLine offer the ability to configure the transmitter and display via three externally accessible buttons when either display option is selected.
• Zero/span capabilities are also optionally available via these buttons with or without selection of a display option.

Hand Held Configuration:

• SmartLine transmitters feature two-way communication and configuration capability between the operator and the transmitter
• This is accomplished via Honeywell’s field-rated
• Multiple Communication Configurator (MCT202).
• The MCT202 is capable of field configuring DE and HART
• Devices and can also be ordered for use in intrinsically safe environments.

Part of the SmartLine family of products, the STG73P is a gauge pressure transmitter with a flush mounted diaphragm. Installed using a 1” sleeve welded to the process piping the diaphragm face may be situated flush with the process piping wall. Typically applied to applications such as head boxes in pulp and paper mills, flush mounting eliminates the possibility of clogging. In addition, the transmitter mounting facilitates rapid and trouble free replacement.

Features:

• Flush mounting design
• Automatic temperature compensation
• Alphanumeric display capabilitiesoExternal zero, span, & configuration capability
• Polarity insensitive electrical connections
• On-board diagnostic capabilities integral Dual
• Seal design for safety based onANSI/NFPA 70-202 and ANSI/ISA 12.27.0
• Full complianceto SIL2/3 requirements as a standard. oModular design characteristics

Description:

• The SmartLine family pressure transmitters are designed around a high performance piezo-resistive sensor.
• This one sensor actually integrates multiple sensors linking process pressure measurement with on-board static pressure (DP Models) and temperature compensation measurements.
• This level of performance allows the ST 700 to replace most competitive transmitters available today.

Basic Alphanumeric LCD Display:

• Modular (may be added or removed in the field)
• 0, 90,180, & 270 degree position adjustments
• Configurable and standard (Pa, KPa, MPa, KGcm2, Torr, ATM, inH2O, mH2O, bar, mbar, inH2O, inHG, FTH2O, mmH2O, mm HG, & psi) measurement units
• 2 Lines 16 Characters (4.13H x 1.83W mm)
• Square root output indication

SimpleLCD Display Features:

• Modular (may be added or removed in the field)
• Supports HART protocol variant
• 0, 90,180, & 270 degree position adjustments
• Configurable (HART only) and standard (Pa, KPa, MPa, KGcm2, Torr, ATM, inH2O, mH2O, bar, mbar, inH2O, inHG, FTH2O, mmH2O, mm HG, & psi) measurement unit
• Supports Flow engineering units
• 2 Lines 6 digitsPV (9.95H x 4.20W mm) 8 Characters
• Square root output indication and Write protect Indication
• Built in Basic Device Configuration through Internal Buttons –Range/Engineering Unit/Loop Test /Loop Calibration/Zero /Span Setting

External Three Button Configuration Option:

• Suitable for all electrical and environmental requirements, SmartLine offers the ability to configure the transmitter and display via three externally accessible buttons when a display option is selected
• Zero/span capabilities are also optionally available via these buttons with or without the selection of the display option.

Internal Two Button Configuration Option:

• The Simple display has two buttons that can be used for Basic configuration such as re-ranging, PV Engineering unit setting, Zero/Span settings, and Loop testing and calibration functions.

Hand Held Configuration:

• SmartLine transmitters feature two-way communication and configuration capability between the operator and the transmitter.
• This is accomplished viaHoneywell’sfield-rated Multiple Communication Configurator (MCT404).
• The MCT404is capable of field configuring DE and HART Devices and can also be ordered for use in intrinsically safe environments
• All Honeywell transmitters are designed and tested for compliance with the offered communication protocols and are designed to operate with any properly validated handheld configuration device

Part of the SmartLine family of products, the STA700 and STA70L are suitable for monitoring, control and data acquisition. STA70X products feature piezoresistive sensor technology combining pressure sensing with on chip temperature compensation capabilities providing high accuracy, stability and performance over a wide range of application pressures and temperatures. The SmartLine family is alsfully tested and compliant with Experion®PKS providing the highest level of compatibility assurance and integration capabilities. SmartLine easily meets the most demanding application needs for pressure measurement applications.

Best in Class Features:

• Automatic temperature compensation
• Easy tuse and intuitive display capabilities
• Intuitive external zero, span, & configuration capability
• On-board diagnostic capabilities
• Integral Dual Seal design for safety based on ANSI/NFPA 70-202 and ANSI/ISA 12.27.0
• Full compliance tSIL 2/3 requirements as a standard.
• Configurable (HART only) and standard (Pa, KPa, MPa, KGcm2, Torr, ATM, inH 2 O, mH 2 O, bar, mbar, in H2O, inHG, FTH 2 O, mmH 2 O, mm HG, & psi) measurement units
• Modular (may be added or removed in the field)
• Supports HART protocol variantWrite protect Indication
• Built in Basic Device Configuration through Internal or
• External Buttons-Range/Engineering Unit/Loop Test/Loop Calibration/Zero /Span Setting

Description:

• The SmartLine family pressure transmitters are designed
• around a high performance piezo-resistive sensor
• This one sensor actually integrates multiple sensors linking process pressure measurement with on-board static pressure (DP Models) and temperature compensation measurements

Diagnostics:

• SmartLine transmitters all offer digitally accessible diagnostics which aid in providing advanced warning of possible failure events minimizing unplanned shutdowns, providing lower overall operational costs

System Integration:

• SmartLine communications protocols all meet the most current published standards for HART.
• All ST 700 units are Experion tested to provide the highest level of compatibility assurance

External two button option for zero/span setting:

• Suitable for all electrical and environmental requirements,
• SmartLine offers the ability to configure the transmitter and display, for all basic parameters, via two externally accessible buttons when a display option is selected.
• Zero/span capabilities are also optionally available via two external buttons with or without selection of the display option.

Internal Two Button Configuration Option:

• The Standard display has two buttons that can be used for
• Basic configuration such as re ranging, PV Engineering unit setting, Zero/Span settings, Loop testing and calibration functions

Hand Held Configuration:

• SmartLine transmitters feature two-way communication and configuration capability between the operator and the transmitter
• This is accomplished via Honeywell’s field-rated
• Multiple Communication Configurator (MCT404).
• The MCT404 is capable of field configuring DE and HART
• Devices and can also be ordered for use in intrinsically safe environments.
• All Honeywell transmitters are designed and tested for compliance with the offered communication protocols and are designed to operate with any properly validated hand held configuration device.

Part of the SmartLine family of products, the STG800 and STG80L are high performance gauge pressure transmitter featuring piezoresistive sensor technology combining pressure sensing with on chip temperature compensation capabilities providing high accuracy, stability and performance over a wide range of application pressures and temperatures. The SmartLine family is also fully tested and compliant with Experion PKS providing the highest level of compatibility assurance and integration capabilities. SmartLine easily meets the most demanding application needs for pressure measurement applications.

Best in Class Features:

• Automatic temperature compensation
• Multiple local display capabilities
• External zero, span, & configuration capability
• Polarity insensitive electrical connections
• Comprehensive on-board diagnostic capabilities
• Integral Dual Seal design for safety based on ANSI/NFPA 70-202 and ANSI/ISA 12.27.0.
• Modular design characteristics.
• Available with a 15-year warranty.
• Plugged Impulse Line Detection Option.
• Full compliance with SIL 2/3 requirements as a standard
• Dual/Triple Calibration Option (HART & Fieldbus Only)

Description:

• The SmartLine family of gauge pressure, differential pressure, and absolute pressure transmitters is designed around a high-performance piezo-resistive sensor
• This one sensor actually integrates multiple sensors linking process pressure measurement with onboard static pressure (DP Models) and temperature compensation measurements resulting in the best total performance available
• This level of performance allows the ST 800 to replace virtually any competitive transmitter available today.

Unique Indication/Display Options:

• The ST 800 modular design accommodates a basic alphanumeric LCD display
• A unique advanced graphics LCD display with many unparalleled features.

Basic Alphanumeric LCD Display Features:

• Modular (may be added or removed in the field)
• 0, 90,180, & 270 degree position adjustments
• Configurable (HART only) and standard (Pa, KPa, MPa, KGcm2, Torr, ATM, inH2O, mH2O, bar, mbar, inH2O, inHG, FTH2O, mmH2O, mm HG, & psi) measurement units
• 2 Lines 16 Characters (4.13H x 1.83W mm)
• Square root output indication

Advanced Graphics LCD Display Features:

• Modular (may be added or removed in the field)
• 0, 90, 180, & 270 degree position adjustments
• Standard and custom measurement units available.
• Up to eight display screens with 3 formats are possible (Large PV with Bar Graph or PV with Trend Graph)
• Configurable screen rotation timing (1 to 30 sec)
• Display Square Root capabilities may be set separately from the 4-20mA dc output signal
• Unique “Health Watch” indication provides instant visibility of diagnostics
• Multiple language capability. (EN, GE, FR, IT, SP, RU, TR, CN, JP)

Integral Three Button Configuration Option:

• Suitable for all electrical and environmental requirements
• SmartLine offer the ability to configure the transmitter and display via three externally accessible buttons when either display option is selected
• Zero/span capabilities are also optionally available via these buttons with or without the selection of a display option

Part of the SmartLine family of products, the STD700 models are suitable for monitoring, control and data acquisition. These products feature piezoresistive sensor technology combining pressure sensing with on-chip temperature compensation capabilities providing high accuracy, stability and performance over a wide range of application pressures and temperatures. The SmartLine family is also fully tested and compliant with Experion PKS providing the highest level of compatibility assurance and integration capabilities. SmartLine easily meets the most demanding application needs for pressure measurement applications.

Features:

• Automatic static pressure & temperature compensation
• Response times as fast as 100ms
• Easy to use and intuitive display capabilities
• Intuitive External Zero, Span and configuration
  capability
• On-board diagnostic capabilities
• Integral Dual Seal design for highest safety based on ANSI/NFPA 70-202 and ANSI/ISA 12.27.0
• World class overpressure protection
• Full compliance to SIL 2/3 requirements.

Standard LCD Display Features:

• Modular (may be added or removed in the field)
• Supports HART protocol variant
• 0, 90,180, & 270 degree position adjustments
• Configurable (HART only) and standard (Pa, KPa, MPa, KGcm2, Torr, ATM, inH2O, mH2O, bar, mbar, inH2O, inHG, FTH2O, mmH2O, mm HG, & psi) measurement units.
• Supports Flow engineering units
• 2 Lines 6 digits PV (9.95H x 4.20W mm) 8 Characters
• Square root output indication (√) and Write Protect
• Indication
• Built-in Basic Device Configuration through Internal or
• External Buttons-Range/Engineering Unit/Loop Test /Loop Calibration/Zero /Span Setting

Diagnostics:

• SmartLine transmitters all offer digitally accessible diagnostics which aid in providing advanced warning of possible failure events minimizing unplanned shutdowns, providing lower overall operational costs

System Integration:

• SmartLine communications protocols all meet the most current published standards for Hart
• All ST 700 units are Experion tested to provide the highest level of compatibility assurance

External Two Button Configuration Option:

• Suitable for all electrical and environmental requirements,
• SmartLine offers the ability to configure the transmitter and display, for all basic parameters, via two externally accessible buttons when a display option is selected.
• Zero/span capabilities are also optionally available via two external buttons with or without the selection of the display option.

Internal Two Button Configuration Option:

• The Standard display has two buttons that can be used for Basic configuration such as re ranging
• PV Engineering unit setting, Zero/Span settings, Loop testing and calibration functions.

Hand Held Configuration:

• SmartLine transmitters feature two-way communication and configuration capability between the operator and the transmitter
• This is accomplished via Honeywell’s field-rated
• Multiple Communication Configurator (MCT404)
• The MCT404 is capable of field configuring HART Devices and can also be ordered for use in intrinsically safe environments
• All Honeywell transmitters are designed and tested for compliance with the offered communication protocols and are designed to operate with any properly validated hand held configuration device.

Part of the SmartLine family of products, the STD800 is a high performance differential pressure transmitter featuring piezoresistive sensor technology. By combining differential pressure sensing with on chip static pressure and temperature compensation the STD800 offers high accuracy and stability over a wide range of application pressures and temperatures. The SmartLine family is also fully tested and compliant with Experion  PKS providing the highest level of compatibility assurance and integration capabilities. SmartLine easily meets the most demanding application needs for pressure measurement applications.

Features:

• Automatic static pressure & temperature compensation
• Response times as fast as 90ms
• Multiple local display capabilities
• External zero, span, & configuration capability
• Polarity insensitive electrical connections
• Comprehensive on-board diagnostic capabilities
• Integral Dual Seal design for highest safety based on ANSI/NFPA 70-202 and ANSI/ISA 12.27.0
• World class overpressure protection
• Full compliance to SIL 2/3 requirements.
• Modular design characteristics
• Available with 15 year warranty
• Plugged Impulse Line Detection Option
• Dual/Triple Calibration Option (HART & Fieldbus Only)

Description:

• The SmartLine family of gauge pressure, differential pressure, and absolute pressure transmitters is designed around a high performance piezo-resistive sensor.
• This one sensor actually integrates multiple sensors linking process pressure measurement with on-board static pressure (DP Models) and temperature compensation measurements resulting in the best total performance available.
• This level of performance allows the ST 800 to replace virtually any competitive transmitter available today.

Basic Alphanumeric LCD Display Features:

• Modular (may be added or removed in the field)
• 0, 90,180, & 270 degree position adjustments
• Configurable (HART only) and standard (Pa, KPa, MPa, KGcm2, Torr, ATM, inH2O, mH2O, bar, mbar, inH2O, inHG, FTH2O, mmH2O, mm HG, & psi) measurement units
• 2 Lines 16 Characters (4.13H x 1.83W mm)
• Square root output indication

Advanced Graphics LCD Display Features:

• Modular (may be added or removed in the field)
• 0, 90, 180, & 270 degree position adjustments
• Standard and custom measurement units available
• Up to eight display screens with 3 formats are possible (Large PV with Bar Graph or PV with Trend Graph)
• Configurable screen rotation timing (1 to 30 sec)
• Display Square Root capabilities may be set separately from the 4-20mA dc output signal
• Unique “Health Watch” indication provides instant visibility of diagnostics
• Multiple language capability. (EN, DE, FR, IT, ES, RU, TR, CN & JP)

Hand Held Configuration:

• SmartLine transmitters feature two-way communication and configuration capability between the operator and the transmitter
• This is accomplished via Honeywell’s field-rated
• Multiple Communication Configurator (MCT404).
• The MCT404 is capable of field configuring DE and HART
• Devices and can also be ordered for use in intrinsically safe environments
• All Honeywell transmitters are designed and tested for compliance with the offered communication protocols and are designed to operate with any properly validated hand held configuration device.

Part of the SmartLine family of products, the STR700 is suitable for monitoring, control and data acquisition. STR700 products feature piezoresistive sensor technology combining pressure sensing with on-chip temperature compensation capabilities providing high accuracy, stability and performance over a wide range of application pressures and temperatures. The SmartLine family is also fully tested and compliant with Experion PKS providing the highest level of compatibility assurance and integration capabilities. SmartLine easily meets the most demanding application needs for pressure measurement applications.

Best in Class Transmitter Features:

• Automatic static pressure & temperature compensation
• Local display capabilities
• External zero, span, & configuration capability
• Polarity insensitive electrical connections
• Integral Dual Seal design for highest safety based on ANSI/NFPA 70-202 and ANSI/ISA 12.27.0
• World class overpressure protection
• Full compliance with SIL 2/3 requirements
• Modular design characteristics

Typical Diaphragm Seal applications:

• High Process Temperatures
• Viscous or Suspended Solids
• Highly Corrosive Process Materials
• Sanitary Applications
• Applications with Hydrogen Permeation Possibilities
• Level Applications with Maintenance Intensive Wet Legs
• Applications requiring remote Transmitter Mounting
• Tank Applications with Density or Interface Measurements

Communications/Output Options:

• Honeywell Digitally Enhanced (DE)
• HART (version 7.0)
• Foundation TM Fieldbus

Description:

• The SmartLine family pressure transmitters are designed around a high-performance piezo-resistive sensor
• This one sensor actually integrates multiple sensors linking process pressure measurement with onboard static pressure (DP Models) and temperature compensation measurements.
• This level of performance allows the ST700 to replace most competitive transmitters available today.

Basic Alphanumeric LCD Display Features:

• Modular (may be added or removed in the field)
• 0, 90,180, & 270 degree position adjustments
• Configurable (HART only) and standard (Pa, KPa, MPa, KGcm2, Torr, ATM, inH2O, mH2O, bar, mbar, inH2O, inHG, FTH2O, mmH2O, mm HG, & psi) measurement units
• 2 Lines 16 Characters (4.13H x 1.83W mm)
• Square root output indication

Simple LCD Display Features:

• Modular (may be added or removed in the field)
• Supports HART protocol variant
• 0, 90,180, & 270 degree position adjustments
• Configurable (HART only) and standard (Pa, KPa, MPa, KGcm2, Torr, ATM, inH2O, mH2O, bar, mbar, inH2O, inHG, FTH2O, mmH2O, mm HG, & psi) measurement units.
• Supports Flow engineering units
• 2 Lines 6 digits PV (9.95H x 4.20W mm) 8 Characters
• Square root output indication (√) and Write protect Indication
• Built-in Basic Device Configuration through Internal
• Buttons – Range/Engineering Unit/Loop Test /Loop Calibration/Zero /Span Setting

External Three Button Configuration Option:

• Suitable for all electrical and environmental requirements
• SmartLine offers the ability to configure the transmitter and display via three externally accessible buttons when a display option is selected.
• Zero/span capabilities are also optionally available via these buttons with or without the selection of the display option.

Part of the SmartLine family of products, the STG700 Dual Head and STG700 Inline are suitable for monitoring, control and data acquisition. STG700 Dual Head products feature piezoresistive sensor technology combining pressure sensing with on chip temperature compensation capabilities providing high accuracy, stability and performance over a wide range of application pressures and temperatures. The SmartLine family is also fully tested and compliant with Experion PKS providing the highest level of compatibility assurance and integration capabilities. SmartLine easily meets the most demanding application needs for pressure measurement applications.

Features:

• Automatic temperature compensation
• Easy to use and intuitive display capabilities
• Intuitive External zero & span capability
• On-board diagnostic capabilities
• Integral Dual Seal design for safety based on ANSI/NFPA 70-202 and ANSI/ISA 12.27.0
• Full compliance to SIL 2/3 requirements as a standard

Description:

• The SmartLine family pressure transmitters are designed around a high performance piezo-resistive sensor
• This one sensor actually integrates multiple sensors linking process pressure measurement with on-board static pressure (GP Models) and temperature compensation measurements

Stamdard LCD Display Features:

• Modular (may be added or removed in the field)
• Supports HART protocol variant
• 0, 90,180, & 270 degree position adjustments
• Configurable (HART only) and standard (Pa, KPa, MPa, KGcm2, Torr, ATM, inH2O, mH2O, bar, mbar, inH2O, inHG, FTH2O, mmH2O, mm HG, & psi) measurement units
• 2 Lines 6 digits PV (9.95H x 4.20W mm) 8 Characters
• Square root output indication (√) and Write protect Indication
• Built in Basic Device Configuration through Internal or
• External Buttons – Range/Engineering Unit/Loop Test /Loop Calibration/Zero /Span Setting

System Integration:

• SmartLine communications protocols all meet the most current published standards for HART.
• All ST 700 units are Experion tested to provide the highest level of compatibility assurance

Hand Held Configuration:

• SmartLine transmitters feature two-way communication and configuration capability between the operator and the transmitter.
• This is accomplished via Honeywell’s field-rated
• Multiple Communication Configurator (MCT404).
• The MCT404 is capable of field configuring HART Devices and can also be ordered for use in intrinsically safe environments.
• All Honeywell transmitters are designed and tested for compliance with the offered communication protocols and are designed to operate with any properly validated hand held configuration device.

Modular Design:

• To help contain maintenance & inventory costs, all ST 700 transmitters are modular in design supporting the user’s ability to replace meter bodies, standard displays or electronic modules without affecting overall performance.
• Each meter body is uniquely characterized to provide intolerance performance over a wide range of application variations in temperature and pressure.